Sensor and Modules Boards
Boardoza Quectel FC41D BT&WiFi Breakout Board
FC41D is a MCU Wi-Fi and Bluetooth module launched by Quectel. It boasts a high-performance processor with a frequency of up to 120 MHz.
Boardoza LM75A Temperature Sensor Breakout Board
The Boardoza LM75ADP is a temperature-to-digital converter using an on-chip band gap temperature sensor and Sigma-delta A-to-D conversion technique.
Boardoza BA6208 Motor Driver Breakout Board
BA6208 is designed for driving reversible motor use, it contain a logic section to controls forward and reverse rotations as well as forced stop.
Boardoza TP4056 Lithium Battery Charger Breakout Board
Boardoza TP4056 is a complete constant-current/constant-voltage linear charger module for single cell lithium-ion batteries.
Boardoza MQ4 Methane Gas Sensor Breakout Board
The MQ-4 methane gas sensor detects the methane (CNG) natural gas density between 300 ppm and 10000 ppm.
Boardoza MS5611 Breakout Board
The MS5611-01BA is a new generation of high resolution altimeter sensors from MEAS Switzerland with SPI and I2C bus interface.
Boardoza ADXL345 Triple Axis Accelerometer Breakout Board
he ADXL345 is a small, thin, low power, 3-axis MEMS accelerometer with high resolution (13-bit) measurement at up to +-16 g.
Boardoza BS801C Capacitive Touch Sensor Breakout Board
The Boardoza BS801C is a capacitive touch sensor board which can detect human body contact using external touch pad.
Boardoza AMS1117-3V Voltage Regulator Breakout Board
Boardoza AMS1117-3V module is designed to provide 3.3V and up to 1A output current and to operate down to 1V input-to-output differential.
Boardoza GP 02 GPS Breakout Board
GP-02 is a high-performance BDS/GNSS multi-mode satellite navigation receiver SOC module, which integrates RF front-end, digital baseband processor, 32-bit RISC CPU, power management and active antenna detection and protection functions.
Boardoza AMS1117-5V Voltage Regulator
Boardoza AMS1117-5V module is designed to provide 5V and up to 1A output current and to operate down to 1V input-to-output differential.
Boardoza Data Logger
“With “Bordoza Data Logger” allows you to record data to SD card such as location, 3 axis gyro-acceleration-magnetic field, pressure, altitude, temperature and speed on your kite or rc aircraft etc.
Boardoza BNO055 IMU Sensor
BNO055 9DOF IMU Sensor The smart sensor BNO055 is a System in Package (SiP) solution that integrates a triaxial 14-bit accelerometer.
Boardoza UBLOX SAM M8Q GPS Module
The u-blox concurrent SAM-M8Q GNSS patch antenna module benefits from the exceptional performance of the u-blox M8 multi-GNSS engine.
Boardoza NSP2340T16L Audio Board
NSP2340T16L series are powerful Voice IC with embedded Flash to implement Voice Assistance applications with Cap Touch.
Boardoza MMA8451 Accelerometer Breakout Board
The MMA8452Q is a smart low-power, three-axis, capacitive micro machined accelerometer with 12 bits of resolution.
Boardoza TH09C Temp Sensor
The TH09C integrates one relative humidity sensor and one highaccuracy temperature sensor.
Boardoza TPS630702RNMT Buck Boost Converter
The TPS630702 is a high efficiency, low quiescent current buck-boost converter suitable for applications where the input voltage can be higher or lower than the output voltage.
Boardoza BQ24650 Battery Charge Controller
The BQ24650 device is a highly integrated switch-mode battery charge controller. It provides input voltage regulation, which reduces charge current when input voltage falls below a programmed level. When the input is powered by a solar panel, the input regulation loop lowers the charge current so that the solar panel can provide maximum power output.
Boardoza FT800 TFT Driver
FT800 is an easy-to-use graphics controller for embedded applications to create high-quality Human Machine Interfaces (HMIs). This board also has audio and speakers output. It provides communication using the SPI interface. Support for LCD display in WQVGA (480×272) and QVGA (320×240)
Boardoza FT810 TFT Driver
FT810 is an easy-to-use graphics controller for embedded applications to create high-quality Human Machine Interfaces (HMIs). This board also has audio and speakers output. It provides communication using the SPI interface. Support for LCD display with resolution up to SVGA (800×600) and formats with data enable (DE) mode or VSYNC/HSYNC mode.
Boardoza HP303B Air Pressure Sensor
The HP303B is a miniaturized Digital Barometric Air Pressure Sensor with a high accuracy and a low current consumption, capable of measuring both pressure and temperature. Sensor measurements and calibration coefficients are available via serial I2C or SPI interface, which we can set.
Boardoza HX711 Analog Digital Converter(ADC)
HX711 is a precision 24-bit analog digital converter (ADC) designed for weigh scales and industrial control applications to interface directly with a bridge sensor. It is possible to use both outputs of the integrated circuit.
Boardoza PYD1598 PIR Sensor
PYD1598 is a PIR (Passive Infrared) sensor from Excelitas Technologies. It uses human body heat for motion detection and is often used in automatic light control applications.
Boardoza SM351LT Hall Effect Sensor
SM351LT is a high-precision Hall effect sensor. It features a Push-Pull output structure and exhibits omnipolar characteristics, capable of detecting both polarities of the magnetic field.
Boardoza TPIS1385 Presence Sensor
It is a presence sensor from Excelitas. It detects presence status depending on temperature. It can detect human presence from up to 3 meters away. Communication is provided via the I2C protocol.
Boardoza W25Q40CLSNIG SPI Flash
W25Q40CLSNIG is a high performance and low power consumption SPI flash memory chip. It has a storage capacity of 4 megabits (512 kilobytes) and provides fast data access. This chip can be used for data storage and code storage in various electronic projects.
Boardoza NAU7802 Analog Digital Converter(ADC)
NAU7802 is a precision low-power 24-bit analog-to-digital converter (ADC). It has two different outputs available. Communication is provided via the I2C protocol.
Boardoza MCP73831 Charge Management Controller
The MCP73831/2 devices are highly advanced linear charge management controllers for use in space-limited, cost-sensitive applications. The MCP73831/2are available in an 8-Lead, 2 mm x 3 mm DFN packageor a 5-Lead, SOT-23 package. Along with their smallphysical size, the low number of external components required make the MCP73831/2 ideally suited forportable applications.
Boardoza DRV8317 BLDC Driver
DRV8317 is an integrated three-phase DC motor driver that supports voltage up to 24V and current up to 5A. It can be controlled via SPI interface and supports PWM frequency up to 200 kHz. It has integrated protection features (UVLO, OVP, CPUV, OCP, OTW/OTS).
Boardoza ESP01M Wi-Fi Module
ESP-01M is a compact Wi-Fi module using the ESP8266 chip. It operates at 2.4 GHz frequency and offers low power consumption and high performance. It easily communicates data with devices via UART.
Boardoza TPS63030 Single Inductor Buck-Boost Converter
The TPS6303x devices provide a power supply solution for products powered by either a two-cell or three-cell alkaline. NiCd or NiMH battery, or a e cel -Hon or Li-polymer battery. Output currents can go as high as 600 mA while using a single-cell Li-ion or L-polymer battery, and discharge it down to 25 V or lower.
Boardoza MDBT50Q Bluetooth Module
MDBT50Q is a Bluetooth module developed by Nordic Semiconductor. Featuring Bluetooth 5.2 features, this module offers long battery life with low power consumption and provides a wide wireless communication range.
Boardoza DRV8307 48W BLDC Driver
This is a three phase brushless BLDC motor driver board. DRV8307 integration and CSD88537ND mosfets are used. SN74CBT3244CPW and SN74LVC2G17DBVR are used for Hall sensor. The board operates with 24V supply voltage. Maximum current capacity is 2A. You can adjust the speed of the board either with a potentiometer or by giving PWM from the PWM pin. You can control direction with S1 switch. It can work with all kinds of hall sensors.
Boardoza HIH8131-021-001 Temperature-Humidity Sensor
This board is used for humidity and temperature measurements and can transmit data digitally thanks to the I2C interface.If you solder JP1 and JP2, you can communicate with I2C. If you do not solder, you communicate with SPI.
Boardoza MicroSD Breakout Board
The MicroSD Breakout Card allows us to read micro sd card in spi communication protocol. This board allows you to utilize a microSD card at top speed on a 3V3 system. With this small breakout board size of 20x40mm, adding mass storage to your project will never be easier.
Boardoza RFM6601W LoRa Module
The RFM6601W is a LoRa wireless communication module designed by HOPERF. It contains a LoRa wireless communication chip, an RF transmitter/receiver and a 32-bit RISC microcontroller (MCU). This MCU uses the ARM Cortex M4 processor and has an operating frequency of 48 MHz. The RF transmitter/receiver has continuous frequency coverage from 150 MHz to 960 MHz.
Boardoza MH2024K MP3 Player
This card is a mini MP3 card. The card has one speaker output. The module can be used as a standalone module with installed battery, speaker and push buttons, or it can be used with Arduino, ESP32, Raspberry Pi and any microcontroller with Uart. Fully supports FAT16 , FAT32 file system, maximum support 32G of the TF card, support 32G of U disk, 64M bytes NORFLASH
Boardoza NT3H2111W0FHKH RFID Reader
NT3H1101 NTAG I2C energy harvesting NFC Forum Type 2 Tag from NXP. Designed to be the perfect enabler for NFC in home-automation and consumer applications, this feature-packed, second-generation connected NFC tag is the fastest, least expensive way to add tap-and-go connectivity to just about any electronic device.
Boardoza TPiS 1T 1386 Temperature Sensor
This board is a temperature sensor board that measures temperature without contact. Excelitas’ TPiS 1T 1386 L5.5 H sensor is used as the temperature sensor. This sensor provides thermal stabilization in harsh conditions. It communicates with I2C.
Boardoza SEEED-316040171 Vibration Motor Driver
This card is a vibration motor driver card. It is powered by +3.3V / +5V and the board can supply 80 mA current for DC motor.
Boardoza SEEED-316040171 Vibration Motor Driver
This card is a vibration motor driver card. It is powered by +3.3V / +5V and the board can supply 80 mA current for DC motor.
